Oil-resistant, Long-range Photoelectric Sensor with Metal Housing E3S-C CSM_E3S-C_DS_E_6_1 Water- and Oil-resistant Photoelectric Sensor with Metal Housing Used for Longrange Sensing * Excellent resistance against the water and oil. Easy application in locations with oil mist. * Long-range sensing up to 30 m with Through-beam models. * Shock resistance rated at 1,000m/s2. * Product lineup includes metal M12 pre-wired connector models. * NPN/PNP selector switch output. Be sure to read Safety Precautions on page 6. Ordering Information Sensors (Refer to Dimensions on page 8.) Sensing method Appearance Red light Connection method Sensing distance E3S-CT11 2M Emitter E3S-CT11-L 2M Receiver E3S-CT11-D 2M E3S-CT11-M1J 0.3M Emitter E3S-CT11-L-M1J 0.3M Receiver E3S-CT11-D-M1J 0.3M 30 m E3S-CT61 2M Emitter E3S-CT61-L 2M Receiver E3S-CT61-D 2M E3S-CT61-M1J 0.3M Emitter E3S-CT61-L-M1J 0.3M Receiver E3S-CT61-D-M1J 0.3M Pre-wired Horizontal Pre-wired Connector (M12) Through-beam (Emitter + Receiver) * Vertical Pre-wired Pre-wired Connector (M12) Horizontal Infrared light Model Pre-wired E3S-CR11 2M Pre-wired Connector (M12) E3S-CR11-M1J 0.3M Retro-reflective 3m Vertical Pre-wired E3S-CR61 2M Pre-wired Connector (M12) E3S-CR61-M1J 0.3M Pre-wired Horizontal Pre-wired Connector (M12) Diffuse-reflective Vertical Pre-wired Pre-wired Connector (M12) 700 mm E3S-CD11 2M 2m E3S-CD12 2M 700 mm E3S-CD11-M1J 0.3M 2m E3S-CD12-M1J 0.3M 700 mm E3S-CD61 2M 2m E3S-CD62 2M 700 mm E3S-CD61-M1J 0.3M 2m E3S-CD62-M1J 0.3M * Through-beam Sensors are normally sold in sets that include both the Emitter and Receiver. Orders for individual Emitters and Receivers are accepted. 1 E3S-C Accessories (Order Separately) Slits (A Slit is not provided with Through-beam Sensors. Order a Slit separately if required.) (Refer to Dimensions on page 10.) Slit width Sensing distance 0.5 mm x 11 mm 1 mm x 11 mm 2 mm x 11 mm 4 mm x 11 mm 1.8 m 3.5 m 7m 15 m Minimum detectable object (typical) 0.5-mm dia. 1-mm dia. 2-mm dia. 2.6-mm dia. Model Quantity 1 set each for Emitter and Receiver (8 Slits total) E39-S61 Remarks (Snap-in Long Slit) Can be used with the E3S-CT@1(-M1J) Through-beam Sensor. Refer to page 10. Reflectors (Reflector required for Retroreflective Sensors) A Reflector is provided with the E39-R1 Sensor. For other Sensors, order a reflector separately if required. (Refer to Dimensions on E39-L/F39-L/E39-S/E39-R.) Name Reflectors Sensing distance (typical) 3 m (rated value) Quantity 1 Remarks Provided with the E3S-CR@1 (-M1J) Retro-reflective Sensor. 4m E39-R2 1 --- 1.5 m E39-R3 1 --- 750 mm E39-R4 1 --- 700 mm (50 mm)* E39-RS1 1 1,100 mm (100 mm)* E39-RS2 1 1,400 mm (100 mm)* E39-RS3 1 Small Reflectors Tape Reflectors Model E39-R1 Enables MSR function. Note: 1. When using any reflector other than the provided one, use a sensing distance of approximately 0.7 times the typical value as a guide. 2. Refer to Reflectors on E39-L/F39-L/E39-S/E39-R for details. * Values in parentheses indicate the minimum distance required between the Sensor and Reflector. Mounting Brackets Some Mounting Brackets are provided with the Sensor. Order other Mounting Brackets separately if required. (Refer to Dimensions on E39-L/F39-L/E39-S/E39-R.) Appearance Model Quantity Remarks E39-L102 1 Provided with Horizontal Models. E39-L103 1 Provided with Vertical Models. E39-L85 1 Mounting bracket for changing from E3S@@@@@42/44 to E3S-C Vertical Models. E39-L86 1 Mounting bracket for changing from E3S@@@@@43 to E3S-C Vertical Models. E39-L87 1 --- Note: 1. When using a Through-beam Sensor, order one Connector for the Receiver and one for the Emitter. 2. Refer to Mounting Brackets on E39-L/F39-L/E39-S/E39-R for details. Sensor I/O Connectors (Models with Pre-wired Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.) (Refer to Dimensions on XS2.) Cable Appearance Straight Cable type Model 2m XS2F-D421-DC0-A 5m Standard L-shape 2m 5m XS2F-D421-GC0-A 3-wire XS2F-D422-DC0-A XS2F-D422-GC0-A Note: 1. When using a Through-beam Sensor, order one Connector for the Receiver and one for the Emitter. 2. For details on Sensor I/O Connectors and cables such as vibration-proof robot cables, refer to Introduction to Sensor I/O Connectors. 2 E3S-C Ratings and Specifications Sensing method Model Item Through-beam Retro-reflective (with M.S.R. function) *1 Horizontal E3S-CT11(-M1J) Horizontal E3S-CR11(-M1J) Horizontal E3S-CD11(-M1J) Horizontal E3S-CD12(-M1J) Vertical E3S-CT61(-M1J) Vertical E3S-CR61(-M1J) Vertical E3S-CD61(-M1J) Vertical E3S-CD62(-M1J) Sensing distance 30 m 3 m (when using E39-R1) Standard sensing object Opaque, 15-mm dia. min. Opaque, 75-mm dia. min. Differential travel --- Diffuse reflective 700 mm (300 x 300 mm white paper) 2m (300 x 300 mm white paper) --- 20% max. of sensing distance Directional angle Emitter and Receiver: 3 to15 3 to 10 Light source (wavelength) Infrared LED (880 nm) Red LED (700 nm) Power supply voltage 10 to 30 VDC including 10% (p.p) ripple Current consumption 50 mA max. (Emitter 25 mA max. Receiver 25 mA max.) Control output Load power supply voltage: 30 VDC max. Load current: 100 mA max. (Residual voltage: NPN output: 1.2 V max., PNP output: 2.0 V max.) Open controller output (NPN/PNP selectable) Light-ON/Dark-ON selectable Protection circuits Power supply reverse polariPower supply reverse polarity protection, Output short-circuit protection, ty circuit protection, Output Mutual interference prevention short-circuit protection Response time Operate or reset: 1 ms max. Sensitivity adjustment One-turn adjuster Ambient illumination (Receiver side) Incandescent lamp: 5,000 lx max. Sunlight: 10,000 lx max. Ambient temperature range Operating: -25C to 55C, Storage: -40C to 70C (with no icing or condensation) Ambient humidity range Operating: 35% to 85%, Storage: 35% to 95% (with no condensation) Insulation resistance 20 M min. (at 500 VDC) Dielectric strength 1,000 VAC, 50/60 Hz for 1 min Vibration resistance Destruction: 10 to 2,000 Hz, 1.5-mm double amplitude or 300 m/s2 for 0.5 hours each in X, Y, and Z directions Shock resistance Destruction: 1,000 m/s2 3 times each in X, Y, and Z directions Degree of protection IEC 60529: IP67 (in-house standards: oil-resistant), NEMA: 6P (indoors only) *2 Connection method Pre-wired (standard cable length: 2 m) or Pre-wired M12 Connector (standard cable length: 0.3 m) Weight (packed state) Approx. 270 g (Pre-wired cable) Approx. 230 g (Pre-wired Connector (M12)) Case Material --Infrared LED (880 nm) 40 mA max. Operate or reset 2 ms max. Two-turn endless adjuster with an indicator Approx. 160 g (Pre-wired cable) Approx. 130 g (Pre-wired Connector (M12)) Approx. 150 g (Pre-wired cable) Approx. 110 g (Pre-wired Connector (M12)) Zinc die-cast Operation PES (polyether sulfone) panel cover Lens Methacrylic resin Mounting Bracket Stainless steel (SUS304) Accessories Mounting Bracket (with screws), Adjustment screwdriver, Instruction manual, and Reflector (only for Retro-reflective Sensors) *1. Refer to MSR function of Technical Guide (Technical version). *2. NEMA: National Electrical Manufactures Association 3 E3S-C Engineering Data (Typical) Parallel Operating Range Through-beam Retro-reflective E3S-CT@ (-M1J) E3S-CT@ (-M1J) + E39-S61 Slit (Order Separately) E3S-CR@1 (-M1J) + E39-R1 Reflector (Provided) 2 Y 1.5 X 1 800 Distance Y (mm) 2.5 Distance Y (mm) Distance Y (m) Through-beam Slit width: 4 mm 600 Slit width: 2 mm 400 Slit width: 1 mm Y 200 0.5 400 E39-R1 Reflector Y 300 X 200 100 X 0 10 20 30 -0.5 0 40 Distance X (m) -1 4 8 12 0 16 Distance X (m) -200 2 3 4 Distance X (m) -100 -400 -1.5 1 -200 Slit width: 0.5 mm -2 -2.5 -600 -300 -800 -400 Operating Range Diffuse-reflective Distance Y (mm) E3S-CD@@ (-M1J) 50 Sensing object: white paper 40 300 x 300 mm E3S-CD@2 Y 30 X E3S-CD@1 20 10 0 1 2 3 Distance X (m) -10 -20 -30 -40 -50 Excess Gain vs. Set Distance Diffuse-reflective E3S-CT@1 (-M1J) E3S-CR@1 (-M1J) + E39-R1 Reflector (Provided) E3S-CD@@ (-M1J) Excess gain ratio 500 300 100 Excess gain ratio Retro-reflective Excess gain ratio Through-beam 500 Reflector: E39-R1 300 100 500 Sensing object: White paper 300 x 300 mm 300 E3S-CD@1 100 50 50 50 30 30 30 10 10 10 5 5 5 3 3 3 Operating 1 level 0 10 20 30 40 Distance (m) Operating 1 level 0 Operating 1 level 1 2 3 4 Distance (m) 0 E3S-CD@2 1 2 3 Distance (m) 4 E3S-C I/O Circuit Diagrams NPN Output Operation mode Model Operation selector Timing charts Incident light No incident light Light-ON Output circuits Through-beam Model Receivers: Retro-reflective Models, Reflective Models Light indicator ON (Red) OFF ON Output transistor OFF L side (LIGHT ON) Light indicator Stability indicator (Green) (Red) Photoelectric Sensor main circuit Operate Load (e.g. relay) Reset (Between brown and black leads) E3S-CT11(-M1J) * E3S-CT61(-M1J) * Dark-ON E3S-CD11(-M1J) E3S-CD12(-M1J) E3S-CD61(-M1J) E3S-CD62(-M1J) 4 Load current Black * Control output ZD 0V Blue * Set the NPN or PNP selector to NPN. Connector Pin Arrangement D side (DARK ON) ON OFF Output transistor 10 to 30 VDC Load NPN or PNP output selector NPN output transistor Brown ZD 3 Incident light No incident light Light indicator ON (Red) OFF E3S-CR11(-M1J) E3S-CR61(-M1J) 1 PNP output transistor 1 2 Operate Load (e.g. relay) Reset 4 3 (Between brown and black leads) Pin 2 is not used. Through-beam Model Emitters Power indicator (Red) 1 Brown Connector Pin Arrangement 1 Photoelectric Sensor main circuit 10 to 30 VDC 2 4 3 3 Blue Note: Pins 2 and 4 are not used. PNP Output Operation mode Model Light-ON Operation selector Timing charts Incident light No incident light Light indicator ON (Red) OFF ON Output transistor OFF Operate Load (e.g. relay) Reset Output circuits Through-beam Model Receivers: Retro-reflective Models, Reflective Models L side (LIGHT ON) Light indicator Stability indicator (Green) (Red) Photoelectric Sensor main circuit (Between blue and black leads) E3S-CT11(-M1J) * E3S-CT61(-M1J) * E3S-CR11(-M1J) E3S-CR61(-M1J) Dark-ON E3S-CD11(-M1J) E3S-CD12(-M1J) E3S-CD61(-M1J) E3S-CD62(-M1J) 1 PNP output transistor Incident light No incident light Light indicator ON (Red) OFF ON Output transistor OFF * NPN or PNP output selector NPN output transistor Brown 10 to 30 VDC ZD 4 Black Control output Load ZD Blue 3 Load current 0V * Set the NPN or PNP selector to NPN. Connector Pin Arrangement D side (DARK ON) 1 2 Operate Load (e.g. relay) Reset 4 3 (Between blue and black leads) Pin 2 is not used. Through-beam Model Emitters Brown Power indicator (Red) Connector Pin Arrangement 1 1 Photoelectric Sensor main circuit 10 to 30 VDC 2 4 3 Blue Note: Pins 2 and 4 are not used. 3 * Models numbers for Through-beam Sensors (E3S-CT@1(-M1J)) are for sets that include both the Emitter and Receiver. The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3S-CT11-L 2M), the model number of the Receiver, by adding "-D" (example: E3S-CT11-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers. Plug (Sensor I/O Connector) Terminal No. 2 3 1 4 1 2 3 4 Brown Classification Blue Black DC XS2F-D421-DC0-A Conductor Connector pin No. Brown 1 Refer to Introduction to Sensor I/O connectors for Power supply (+V) details. Application --- 2 --- Blue 3 Power supply (0 V) Black 4 Output Note: Pin 2 is not used. 5 E3S-C Nomenclature Horizontal Model Vertical Model Operation panel cover Stability indicator (green) S L Light indicator (red) Operation panel cover Stability indicator (green) S PNP Max SENS PNP NPN Sensitivity adjuster D*ON Output selector *1 L*ON E3S-CD12 Operation selector *2 Model number Light indicator (red) SENS Output selector *1 NPN Min L D ON Min L ON Max Sensitivity adjuster Operation selector *2 Note: The sensitivity adjuster on Through-beam and Retro-reflective Models is different. *1. Use the output selector to select the type of output transistor, NPN or PNP. *2. Use the operation selector to select the operation mode. Safety Precautions Refer to Warranty and Limitations of Liability. WARNING This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. Precautions for Correct Use Do not use the product in atmospheres or environments that exceed product ratings. Designing Fuzzy Mutual Interference Prevention Function If Reflective Sensors are installed side by side, each Sensor may be influenced by the light emitted from the other Sensors. The fuzzy mutual interference prevention function of the E3S-C enables the E3S-C to monitor any light interference for a certain period before the E3S-C starts emitting light so that the E3S-C can retrieve the intensity and frequency of the light interference as data. Using this data, the E3S-C estimates with fuzzy inference the risk of the malfunctioning of the E3S-C and controls the timing of the E3SC's light emission. Mounting Bracket * When mounting the E3S-C with the mounting bracket so that sensing objects will be in the direction of the mechanical axis, use the optical axis lock holes. * If it is not possible to mount the E3S-C so that the sensing objects will be in the direction the mechanical axis, move the E3S-C upwards, downwards, to the left, or to the right and secure the E3SC in the center of the range where the light indicator will be lit, at which time make sure that the stability indicator is lit. Direct Mounting Mount the E3S-C as shown in the following illustration. Mounting with M4 Screws Two, 4.5 dia. through holes M4 M4 hole M4 hole Mounting with M3 Screws When the risk is low: The E3S-C waits until there is no light interference and emits light. Two, M3 Light interference Emission pattern M4 hole When the risk is high: The E3S-C emits light between each period of light interference. Light interference Emission pattern Wiring Cable * The E3S-C uses an oil-resistive cable to ensure oil resistivity. * Do not allow the cable to be bent to a radius of less than 25 mm. M4 hole M3 Optical Axis Adjustment Optical Lock Holes By inserting screws into the optical axis lock holes, the Mounting Bracket will be in the direction of the optical axis of the E3S-C. Optical axis Mounting axis Four optical axis lock holes (M4) Mounting Mounting * When mounting the E3S-C, do not hit the E3S-C with a hammer, or the E3S-C will loose watertightness. * Use M4 screws to mount the E3S-C. The tightening torque of each screw must be 1.18 N*m maximum. 6 E3S-C Adjusting Optical Axis of Through-beam Sensor The E3S-C Through-beam Models incorporates two lenses, one of which will be used as shown in the following illustration. When using a Slit, the Slit must be on the side where the lens to be used is located. Horizontal Model Vertical Model Lens in use. The Slit must be on this side. Lens in use. Others Oil and Chemical Resistance * Although the E3S-C is oil-resistance, refer to the following table before using the E3S-C in places where oil may be sprayed on the E3S-C. * Tests were carried out with the following oils and it was certified that the E3S-C resists these oils. Oil Lubricating oil Water insoluble machining oil Unused lens Unused lens Water soluble machining oil Product name Kinematic viscosity (mm2/s (cst)) at 40C Velocite No.3 2.02 Yushiron Oil No. 2 ac Less than 10 To ensure the water resistance of the E3S-C, tighten the screws of the operation panel cover to a torque of 0.34 N*m to 0.54 N*m. --- Yushiroken EC50T-3 7 to 9.5 Yushiron Lubic HWC68 7 to 9.9 Griton 1700D Yushiroken S50N Water Resistance PH --- 7 to 9.2 7 to 9.8 Note: 1. The E3S-C maintained a minimum insulation resistance of 100 M after the E3S-C was dipped in all the above oils at a temperature of 50C for 240 hours. 2. When using the E3S-C in a place where an oil other than the ones listed above is sprayed on the E3S-C, refer to the above kinematic viscosity and ph values. The location may be suitable for the E3S-C if the kinematic viscosity and pH values of the oil are close to the above kinematic viscosity and pH values, but make sure that the oil does not contain any additive that may have a negative influence on the E3S-C. 7 E3S-C (Unit: mm) Dimensions Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified. Sensors Through-beam (Horizontal) E3S-CT11(-M1J) Pre-wired Connector (-M1J) 4-dia. vinyl-insulated round cable Standard length: 300 mm With Mounting Bracket Attached 18.5 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.2 mm2 (AWG 24), Insulator diameter: 1.2 mm), Standard length: 2 m *3 M3 x 5 50 M12 x 1 *2 Light indicator (red) 20 20.4 Mounting Holes 22.2 Stability indicator (green) Emitter: E3S-CT@@-L Receiver: E3S-CT@@-D Two, M4 20 4.2 9.2 25.4 4.2 Lens (17 x 11) 6.2 Optical axis 8.3 Stainless steel (SUS304) 38.2 2.2 4 23 29.5 18 17.3 9.3 A*1 Two, M4 1.5 20.8 25.4 *1. The Mounting Bracket can be attached to side A. *2. The Emitters for Through-beam Sensors only have the power indicator (red). *3. The Emitter cable is 4-dia.vinyl-insulated round cable with 2 conductors (conductor cross section: 0.3 mm2, insulator diameter: 1.3 mm) and a standard length of 2 m. Note: Models numbers for Through-beam Sensors (E3S-CT11(-M1J)) are for sets that include both the Emitter and Receiver. The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3S-CT11-L 2M), the model number of the Receiver, by adding "-D" (example: E3S-CT11-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers. 8 E3S-C Through-beam (Vertical) E3S-CT61(-M1J) Pre-wired Connector (-M1J) 4-dia. vinyl-insulated round cable Standard length: 300 mm With Mounting Bracket Attached M12 x 1 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.2 mm2 (AWG24), Insulator diameter: 1.2 mm), Standard length: 2 m *3 57 Optical axis 15.8 7.4 Optical axis 20 20.4 Mounting Holes 22.2 Lens (17 x 11) Two, M4 4.2 20 9.2 25.4 4.2 4.2 Stainless steel (SUS304) 12.9 12.9 25.4 31 Stability indicator (green) 7.2 Light indicator (red)*2 43.8 2.2 5.8 20.2 23 32.2 A*1 M3 x 5 12 Two, M4 23.2 1.5 *1. The Mounting Bracket can be attached to side A. *2. The Emitters for Through-beam Sensors only have the power indicator (red). *3. The Emitter cable is 4-dia.vinyl-insulated round cable with 2 conductors (conductor cross section: 0.3 mm2, insulator diameter: 1.3 mm) and a standard length of 2 m. Retro-/Diffuse-reflective (Horizontal) E3S-CR11(-M1J) E3S-CD11(-M1J) E3S-CD12(-M1J) Pre-wired Connector (-M1J) 4-dia. vinyl-insulated round cable Standard length: 300 mm With Mounting Bracket Attached 18.5 50 Light indicator (red) M3 x 5 M12 x 1 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.2 mm2 (AWG24), Insulator diameter: 1.2 mm), Standard length: 2 m 20 20.4 Mounting Holes 22.2 Stability indicator (green) Two, M4 20 4.2 9.2 25.4 4.2 Lens (17 x 11) 6.2 Receiver 8.3 Stainless steel (SUS304) 38.2 2.2 23 4 9 29.5 1 18 17.3 9.3 A* Optical axis Emitter Two, M4 1.5 20.8 25.4 *The Mounting Bracket can be attached to side A. Note: Models numbers for Through-beam Sensors (E3S-CT61(-M1J)) are for sets that include both the Emitter and Receiver. The model number of the Emitter is expressed by adding "-L" to the set model number (example: E3S-CT61-L 2M), the model number of the Receiver, by adding "-D" (example: E3S-CT61-D 2M.) Refer to Ordering Information to confirm model numbers for Emitter and Receivers. 9 E3S-C Retro-/Diffuse-reflective (Vertical) E3S-CR61(-M1J) E3S-CD61(-M1J) E3S-CD62(-M1J) Pre-wired Connector (-M1J) 4-dia. vinyl-insulated round cable Standard length: 300 mm With Mounting Bracket Attached M12 x 1 57 Receiver 5 4-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.2 mm2 (AWG24), Insulator diameter: 1.2 mm), Standard length: 2 m 9 2.4 20.8 Emitter Optical axis 20 20.4 Mounting Holes 22.2 Two, M4 Lens (17 x 11) 4.2 9.2 20 25.4 4.2 4.2 12.9 12.9 Stainless steel (SUS304) 25.4 31 Stability indicator (green) 7.2 Light indicator (red) 43.8 2.2 5.8 20.2 23 32.2 A*1 M3 x 5 12 Two, M4 23.2 *The Mounting Bracket can be attached to side A. 1.5 Accessories (Order Separately) Snap-in Long Slit (For Through-beam Models) E39-S61 1 A 0.2 11 6.2 11.8 20 3.8 6.5 20.1 Dimension A (mm) 0.5 1 2 4 Material Stainless steel Quantity 1 set each for Emitter/Receiver (8 Slits total) Reflectors Refer to E39-L/F39-L/E39-S/E39-R for details. Mounting Brackets Refer to E39-L/F39-L/E39-S/E39-R for details. 10 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: * Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. * Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. * Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. 2010.9 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2010 All Right Reserved. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Omron: E3S-CD61-M1J 0.3M E3S-CR61 5M E3S-CR61-M1J 0.3M E3S-CR62-C E3S-CR67-C E3S-CD62 2M